|
|
|
|
|
|
Concealed Door Loop for Continuous and Butt Hinge Applications
|
|
|
This patented Concealed Door Loop (CDL) is a low cost method of transferring low voltage power from the door frame to the locking device. Whereas typical door loops are surface mounted and remain constantly visible, the CDL slides into the door and/or frame completely concealing itself when the door is closed. Designed for Continuous and Butt hinge applications that are either full mortise, half mortise or half surface and have a standard throw. Commonly installed where ETH hinges are cost prohibitive and surface door loops are not desired. The CDL’s aesthetic appeal will benefit retrofits and new installations alike.
Models for butt & continuous hinges:
CDL-AL - Standard 6" length with aluminum finished caps
CDL-BLK - Standard 6" length with black anodized finished caps
CDL-AL-FX - Standard 6" length with aluminum finished caps & 1 side fixed
CDL-BLK-FX - Standard 6" length with black anodized finished caps & 1 side fixed
* For narrow frame and door conditions see 3/4” pivot models (CDL-AL-EXT, CDL-BLK-EXT)
Features:
Durable finish
Special 1/4" flexible armored conduit
Easy installation
Supports up to 18O degree swing
Variable mounting locations
No hassle 3-Year Warranty
Functionality:
|
|
|
|
|
|
|
|
|
|
Concealed Door Loop for Offset Pivot Applications
|
|
|
This patented Concealed Door Loop (CDL) is a low cost method of transferring low voltage power from the door frame to the locking device. Whereas typical door loops are surface mounted and remain constantly visible, the CDL slides into the frame completely concealing itself when the door is closed. Commonly used in storefront or main entrance applications with 3/4” offset pivots that swing up to 105°. The CDL’s aesthetic appeal will benefit retrofits and new installations alike.
Models for 3/4" offset Pivots:
CDL-AL-EXT - 12" length with aluminum finished caps - door side fixed, frame side extended for wire guidance
CDL-BLK-EXT - 12" length with black anodized finished caps - door side fixed, frame side extended for wire guidance
Features:
Durable finish
Special 1/4" flexible armored conduit
Easy installation
Supports up to 105 degree swing
Variable mounting locations
No hassle 3-Year Warranty
|
|
|
|
|
|
|
|
|
|
SW3 Power Supply for Mortise and Cylindrical Locks
|
|
|
SW3
The SW3 power supply is a low cost, regulated switching power supply designed to supply power to low current DC devices such as mortise locks, cylindrical locks and electric strikes. The SW3 supplies a continuous 2.4A @ 27VDC and offers (3) non-fused outputs. The unit is housed in an attractive, high-quality metal enclosure to ensure your project has the quality your customers have come to expect.
|
|
|
|
|
|
|
|
|
|
CA-5 Knuckle Heavy Weight Tranfer Hinge - ETH
|
|
|
The Energy Transfer Hinge (ETH) is the ideal way to pass low voltage power from the hinge jamb to the lockset without having any exposed wires. These hinges are commonly used with electric mortise & cylindrical locks, electric strikes (when on a pair of doors), electric exit trims, latch pullback devices, door mounted card readers and low voltage door lights. We can modify almost any hinge and we maintain a large inventory of most major hinge brands in various sizes and finishes. Contact us if what you need is not listed.
Configurations:
ETH2W: 2 Wire (20 gauge) - 4A@24V (per pair)
ETH4W/6W: 4/6 Wire (26 gauge) - 1A@24V (per pair)
ETH8W/1OW/12W: 8/10/12 Wire (28 gauge) - 1A@24V (per pair)
Configurations Available for Electric Latch Retraction:
ETH2WH: 2 Wire (18 gauge) - 5A (16 amp in-rush for 300 ms.)
ETH4WH - ETH12WH: 4 - 12 Wire (2 wires @ 18 ga. + 2-10 wires 28 ga.)
Features:
UL-F Rated
4' lead available at no extra charge
Center located wire access holes for easy installation (5 Knuckle std. wt.)
Non-conductive wire access cap for added wire protection
No hassle 3-Year Warranty
|
|
|
|
|
|
|
|
|
|
CA-3 Knuckle Heavy Weight Tranfer Hinge - ETH
|
|
|
The Energy Transfer Hinge (ETH) is the ideal way to pass low voltage power from the hinge jamb to the lockset without having any exposed wires. These hinges are commonly used with electric mortise & cylindrical locks, electric strikes (when on a pair of doors), electric exit trims, latch pullback devices, door mounted card readers and low voltage door lights. We can modify almost any hinge and we maintain a large inventory of most major hinge brands in various sizes and finishes. Contact us if what you need is not listed.
Configurations:
ETH2W: 2 Wire (20 gauge) - 4A@24V (per pair)
ETH4W/6W: 4/6 Wire (26 gauge) - 1A@24V (per pair)
ETH8W/1OW/12W: 8/10/12 Wire (28 gauge) - 1A@24V (per pair)
Configurations Available for Electric Latch Retraction:
ETH2WH: 2 Wire (18 gauge) - 5A (16 amp in-rush for 300 ms.)
ETH4WH - ETH12WH: 4 - 12 Wire (2 wires @ 18 ga. + 2-10 wires 28 ga.)
Features:
UL-F Rated
4' lead available at no extra charge
Center located wire access holes for easy installation (5 Knuckle std. wt.)
Non-conductive wire access cap for added wire protection
No hassle 3-Year Warranty
|
|
|
|
|
|
|
|
|
|
CA- Power Transfer Pivot - ETH
|
|
|
The Energy Transfer Pivot Hinge is available in the same wire configurations s the butt hinges. It's a great way to pass power from the hinge jamb to the door and have no exposed wires or cords. We maintain an inventory of our own Command Access intermediate pivot hinge. We also modify other manufacturers pivots if sent to us.
Configurations:
ETH2W = 2(20ga) wire - 4A @ 24V (per pair)
ETH4W = 4(26ga) wire - 1A @ 24V (per pair)
ETH6W = 6(26ga) wire - 1A @ 24V (per pair)
ETH8W = 8(28ga) wire - 1A @ 24V (per pair)
ETH10W = 10(28ga) wire - 1A @ 24V (per pair)
Configurations for Electric Latch Pullback:
ETH2WH = 2(18ga) wire
ETH4WH = 2(18ga) + 2(28ga) wire
ETH6WH = 2(18ga) + 4(28ga) wire
ETH8WH = 2(18ga) + 6(28ga) wire
Features:
Non-conductive wire access cap for added wire protection
4' lead available at no charge
No hassle 3 year warranty
|
|
|
|
|
|
|
|
|
|
CA - Electrified Mortise Lockset Command Access ML1
|
|
|
The Command Access ML1 series lock offers the quality and features found in premium-quality, domestically made ANSI grade 1 mortise locks, yet at a significantly lower cost. The electrification and part tolerance maintenance is done here in the USA to ensure CAT’s high quality standards are met. The ML1’s chassis and trim are compatible with the Schlage “L” series locks so retrofitting to Schlage prep is never a problem.
Models Available:
ML180 (storeroom) – Outside lever locked (EL) or unlocked (EU) electronically. Latchbolt retracted by key outside or lever inside. Switched power allows outside lever to retract latchbolt. Inside lever is always free for immediate egress.
ML182 (institutional) – Outside and inside levers simultaneously locked (EL) or unlocked (EU) electronically. Latchbolt retracted by key on either side. Switched power allows both levers to retract latchbolt.
ML170 (classroom) – Outside lever locked (EL) or unlocked (EU) electronically. Latchbolt retracted lever on either side unless outside has been locked by key. Switched power allows outside lever to retract latchbolt. Inside lever is always free for immediate egress.
ML1480 (entry w/deadbolt) – Outside lever locked (EL) or unlocked (EU) electronically. Latchbolt and deadbolt retracted by key outside or lever inside. Switched power allows outside lever to retract latchbolt and deadbolt. Inside lever is always free for immediate egress.
ML1485 (privacy w/deadbolt) - Outside lever unlocked (EU) electronically. Latchbolt and deadbolt retracted by key outside or lever inside. Switched power allows outside lever to retract latchbolt unless deadbolt is thrown. Inside lever is always free for immediate egress. Available in EU (electronically unlocked) function only
Trims Available: L3, L6, L17 with 2-7/16" rosettes
Finishes available: 613, 625, 626
Features:
UL Listed
Continuous duty solenoids allow for “continuously on” applications such as Fail Safe or an unlock cycle
Plug-in bridge rectifier that allows for an AC or DC power source
Low current draw
Compatible with Schlage “L” series mortise trim.
No hassle 3-Year Warranty
Options:
Available Fail Safe (Electrically Locked) or Fail Secure (Electrically Unlocked)
Voltage options - 12V or 24V(AC/DC)
REX - Request to Exit or AE switch available
LBM - Latchbolt Monitor switch available
DPS - Door Position switch available
DBM - Deadbolt Monitor switch available
SLM - Solenoid Monitor switch available
SCM - Security Monitor switch available
CRU2 - Current Reduction Unit to improve solenoid life in “continuously on” applications
CRU2i - The intelligent CRU2: automatically detects DC input voltage between 12 to 30 volts and converts it to operate our 12V locks. Additionally, it adjusts the current to the solenoid allowing the lockset to run cooler and last longer without any manual adjustments.
Specifications:
Operating Voltage – 12 or 24VAC/DC (+or- 10%) (must specify 12 or 24 volts when ordering)
Amperage – 12V = 700 mA / 24V = 350mA
Solenoid coil resistance – 12V = 18 Ω 24V = 69 Ω
Power consumption – 8 watts
|
|
|
|
|
|
|
|
|
|
CA - Electrified Mortise Lockset Cal Royal
|
|
|
The Command Access electrified version of the Cal-Royal “M” series mortise lock line allows for remote keyless access and egress control for heavy use applications where security and safety is critical. These locks may be purchased as special order complete locks or as modifications only (add MD prefix for modification only of customers’ M8080 lock bodies). Along with the styles and finishes listed below, we offer multiple functions and voltages to meet your requirements. Common applications include stairwell doors, lobby entrances, computer rooms, classrooms, interior and exterior doors. The electrified mortise lock allows remote keyless access and egress control for heavy use applications where security and safety are critical. Common applications include stairwell doors, lobby entrances, computer rooms, classrooms and exterior doors. This Mortise lock may be purchased as a modification only of customers’ lock.
Models Available:
MDML8080 (storeroom) – Outside lever locked (EL) or unlocked (EU) electronically. Latchbolt retracted by key outside or lever inside. Switched power allows outside lever to retract latchbolt. Inside lever is always free for immediate egress.
MDML8053 (entry w/deadbolt) – Outside lever locked (EL) or unlocked (EU) electronically. Latchbolt and deadbolt retracted by key outside or lever inside. Switched power allows outside lever to retract latchbolt and deadbolt. Inside lever is always free for immediate egress.
Trims Available: call to verify
Finishes available: call to verify
Features:
UL Listing
CSFM Listing
Continuous duty solenoids allow for “continuously on” applications such as Fail Safe or an unlock cycle
Plug-in bridge rectifier that allows for an AC or DC power source
Low current draw
No hassle 3-Year Warranty
Options:
Available Fail Safe (Electrically Locked) or Fail Secure (Electrically Unlocked)
Voltage options - 12V or 24V(AC/DC)
REX - Request to Exit or AE switch available
LBM - Latchbolt Monitor switch available
DPS - Door Position switch available
CRU2 - Current Reduction Unit to improve solenoid life in “continuously on” applications
CRU2i - The intelligent CRU2: automatically detects DC input voltage between 12 to 30 volts and converts it to operate our 12V locks. Additionally, it adjusts the current to the solenoid allowing the lockset to run cooler and last longer without any manual adjustments.
Specifications:
Operating Voltage – 12 or 24VAC/DC (+or- 10%) (must specify 12 or 24 volts when ordering)
Amperage – 12V = 700 mA / 24V = 350mA
Solenoid coil resistance – 12V = 18 Ω 24V = 69 Ω
Power consumption – 8 watts
|
|
|
|
|
|
|
|
|
|
Command Access MLRK1-TS - Townsteel ED1000, USCAN 1000 Series Motorized Latch Retraction Kit
|
|
|
The Command Access MLRK-TS1 Motorized Latch Retraction Kit is a highly versatile and innovative device that allows you to easily transform your existing mechanical Townsteel ED1000, or USCAN 1000 series exit devices into an advanced electrified latch pullback system. With its cost-effective design and reliable performance, this kit is the perfect solution for anyone looking to upgrade their security system without breaking the bank. Whether you need to secure your building, office, or other commercial space, the Command Access MLRK-TS1 Motorized Latch Retraction Kit has got you covered. Old Part Number: EDLP2-UL-M-KIT
|
|
|
|
|
|
|
|
|
|
Command Access MLRK1-CAL - Cal-Royal 22 & 98 Series Motorized Latch Retraction Kit
|
|
|
The MLRK1-CAL Motorized Latch Retraction kit, designed by Command Access, is an innovative solution that enables you to convert your existing mechanical Cal-Royal 22 & 98 series exit devices into fully electrified latch pullback devices. This kit is an ideal choice for those seeking an affordable and practical way to upgrade their security systems. With its advanced features, the MLRK1-CAL is a reliable and easy-to-use solution that ensures smooth and secure operation of your exit devices. Say goodbye to manual unlocking and opening of doors and embrace the convenience and security of the MLRK1-CAL Motorized Latch Retraction kit.
|
|
|
|
