Home > Exit Devices
Choose a sub category:
Electric Latch Retraction Conversion Kits Electric Latch Retraction Exit Devices
Manual Exit Devices Power Supplies
Power Supplies Misc Items Power Transfers
Sort By:
Page of 5
Concealed Door Loop for Continuous and Butt Hinge Applications
Concealed Door Loop for Continuous and Butt Hinge Applications
Our Price: $50.00

This patented Concealed Door Loop (CDL) is a low cost method of transferring low voltage power from the door frame to the locking device. Whereas typical door loops are surface mounted and remain constantly visible, the CDL slides into the door and/or frame completely concealing itself when the door is closed. Designed for Continuous and Butt hinge applications that are either full mortise, half mortise or half surface and have a standard throw. Commonly installed where ETH hinges are cost prohibitive and surface door loops are not desired. The CDL’s aesthetic appeal will benefit retrofits and new installations alike.

Models for butt & continuous hinges:

   CDL-AL - Standard 6" length with aluminum finished caps
   CDL-BLK - Standard 6" length with black anodized finished caps
   CDL-AL-FX - Standard 6" length with aluminum finished caps & 1 side fixed
   CDL-BLK-FX - Standard 6" length with black anodized finished caps & 1 side fixed

* For narrow frame and door conditions see 3/4” pivot models (CDL-AL-EXT, CDL-BLK-EXT)
Features:

   Durable finish
   Special 1/4" flexible armored conduit
   Easy installation
   Supports up to 18O degree swing
   Variable mounting locations
   No hassle 3-Year Warranty

Functionality:
more info
Surface Applied Door Loop
Surface Applied Door Loop
Our Price: $50.00

The door loop is a low cost method of transferring low voltage power from the door frame to the locking device. Door loops are commonly used with electric mortise & cylindrical locks, electric exit trims and latch pullback devices.
Configurations:

   DL-24AL - Standard 24" length with aluminum finish
   DL-24D - Standard 24" length with duronatic finish

Features:

   Durable powder coated finish
   Pre-drilled holes in base
   Flexible armored conduit
   No hassle 3-Year Warranty
more info
Concealed Door Loop for Offset Pivot Applications
Concealed Door Loop for Offset Pivot Applications
Our Price: $56.00

This patented Concealed Door Loop (CDL) is a low cost method of transferring low voltage power from the door frame to the locking device. Whereas typical door loops are surface mounted and remain constantly visible, the CDL slides into the frame completely concealing itself when the door is closed. Commonly used in storefront or main entrance applications with 3/4” offset pivots that swing up to 105°. The CDL’s aesthetic appeal will benefit retrofits and new installations alike.

Models for 3/4" offset Pivots:

   CDL-AL-EXT - 12" length with aluminum finished caps - door side fixed, frame side extended for wire guidance
   CDL-BLK-EXT - 12" length with black anodized finished caps - door side fixed, frame side extended for wire guidance

Features:

   Durable finish
   Special 1/4" flexible armored conduit
   Easy installation
   Supports up to 105 degree swing
   Variable mounting locations
   No hassle 3-Year Warranty
more info
DS1 Delay / Sequencer
DS1 Delay / Sequencer
Our Price: $156.00

The DS1 delay/sequencer board offers a switching network that is ideal for (de)energizing an electrified locking device then, after an adjustable time, activating an automatic door operator. It is also suitable for other timing functions such as door sequencing in one or both directions, or anywhere a timing relay is required. For Telephone Entry system applications, the DS1 offers a direct connection to the entry panel, simplifying wiring and eliminating the need for and isolating relay.
Features:

   Bi-Directional sequencing mode
   3 Adjustable delays, up to 30 seconds maximum
   Easy potentiometer adjustments
   LEDs for visual relay confirmation
   Accepts wet or dry inputs
   12 to 24V AC/DC
   One shot design for security or maintained output for smoke evac
   SPDT contacts rated at 3Amps @ 30VDC
   Input for connection to phone
   No hassle 3-Year Warranty

Specifications:

   Size - 3 ¼” x 2 ¼” x ¾”
   Mounting - Velcro or double-sided tape
   Enclosure - Protective paper sleeve
   Operating voltage - 12 / 24 Volts, AC / DC
   Current Draw - 18 mA standby, 40 mA max
   Response time - 0.3 seconds
   Inputs - 2 Wet + 2 Dry contacts: (3-30 V AC/DC, Optically isolated, non-polarity sensitive)
   Relay Output - 2 x Form C (SPDT)
   Relay contact rating - 3 amps @ 20 VDC
   Time Delays - DOR #1 1 to 30 seconds; DOO #2 1 to 30 seconds; DOR #2 1 to 30 seconds
   Electrical Life - 100,000 operations @ rated capacity; 500,000 operations @ ½ rated capacity
more info
VD2 Input / Output Board for PS873
VD2 Input / Output Board for PS873
Our Price: $160.00

Recently Von Duprin has discontinued the PS873 power supply and the add-on boards associated with that power supply. Command Access has developed a replacement board manufactured with similar characteristics to PS871-2 board. The new VD2 board mounts to the PS873 in the same fashion as the factory original PS871-2 board.
Features:

   Solid-State Design
   (2) I/Os w/ Priority Sensing
   Euro Style Connectors
   No hassle 3-Year Warranty
more info
PM300 Power Module
PM300 Power Module
Our Price: $164.00

The patented PM300 power booster module is an interface module that connects between the solenoid circuit of a latch-pullback exit device and the power supply. The PM series modules have been offering a reliable, cost-effective interface solution for exit devices for nearly a decade. The PM300 series modules integrate all the upgrades and improvements we’ve made over the years and are available for nearly all exit device applications.

Over the past decade our customers have discover different uses for this module which include the following:

Allows a solenoid-driven exit device to be used with a lower cost power supply - The PM300 provides a local power boost and will work with most 1.5 A or greater, 24VDC, non-switching power supplies, eliminating the need for the expensive “specialty” power supply.

Longer wire runs from the power supply to the exit device – Since the PM300 is the located in the exit device the allowable distance between the power supply and the exit device without compromising the performance of the device increases significantly

Gives a needed boost to an anemic power supply/exit device installation – For various reason our customers have encountered conditions where the PM300 saves the day! The anemic conditions could be due to marginal power supply, minor device binding, too small of gauge wire run, too long of a wire run to name a few.

more info
CA-5 Knuckle Heavy Weight Tranfer Hinge - ETH
CA-5 Knuckle Heavy Weight Tranfer Hinge - ETH
Our Price: $190.00

The Energy Transfer Hinge (ETH) is the ideal way to pass low voltage power from the hinge jamb to the lockset without having any exposed wires. These hinges are commonly used with electric mortise & cylindrical locks, electric strikes (when on a pair of doors), electric exit trims, latch pullback devices, door mounted card readers and low voltage door lights. We can modify almost any hinge and we maintain a large inventory of most major hinge brands in various sizes and finishes. Contact us if what you need is not listed.
Configurations:

   ETH2W: 2 Wire (20 gauge) - 4A@24V (per pair)
   ETH4W/6W: 4/6 Wire (26 gauge) - 1A@24V (per pair)
   ETH8W/1OW/12W: 8/10/12 Wire (28 gauge) - 1A@24V (per pair)

Configurations Available for Electric Latch Retraction:

   ETH2WH: 2 Wire (18 gauge) - 5A (16 amp in-rush for 300 ms.)
   ETH4WH - ETH12WH: 4 - 12 Wire (2 wires @ 18 ga. + 2-10 wires 28 ga.)

Features:

   UL-F Rated
   4' lead available at no extra charge
   Center located wire access holes for easy installation (5 Knuckle std. wt.)
   Non-conductive wire access cap for added wire protection
   No hassle 3-Year Warranty
more info
CA-3 Knuckle Heavy Weight Tranfer Hinge - ETH
CA-3 Knuckle Heavy Weight Tranfer Hinge - ETH
Our Price: $190.00

The Energy Transfer Hinge (ETH) is the ideal way to pass low voltage power from the hinge jamb to the lockset without having any exposed wires. These hinges are commonly used with electric mortise & cylindrical locks, electric strikes (when on a pair of doors), electric exit trims, latch pullback devices, door mounted card readers and low voltage door lights. We can modify almost any hinge and we maintain a large inventory of most major hinge brands in various sizes and finishes. Contact us if what you need is not listed.
Configurations:

   ETH2W: 2 Wire (20 gauge) - 4A@24V (per pair)
   ETH4W/6W: 4/6 Wire (26 gauge) - 1A@24V (per pair)
   ETH8W/1OW/12W: 8/10/12 Wire (28 gauge) - 1A@24V (per pair)

Configurations Available for Electric Latch Retraction:

   ETH2WH: 2 Wire (18 gauge) - 5A (16 amp in-rush for 300 ms.)
   ETH4WH - ETH12WH: 4 - 12 Wire (2 wires @ 18 ga. + 2-10 wires 28 ga.)

Features:

   UL-F Rated
   4' lead available at no extra charge
   Center located wire access holes for easy installation (5 Knuckle std. wt.)
   Non-conductive wire access cap for added wire protection
   No hassle 3-Year Warranty
more info
PS1-BO Power Supply Board Only
PS1-BO Power Supply Board Only
Our Price: $200.00

Board only to replace the PS1. This is a heavy duty, high quality, low cost solution for powering a single electric latch pullback exit device. The solid-state design ensures years of trouble-free operation. This linear power supply delivers 24VDC current which is ideal for the extreme in-rush requirement of most solenoid driven electric latch retracting exit devices. The power supply comes housed in a sturdy, yet compact metal enclosure.
more info
PS210
PS210 Power Supply
Our Price: $236.00

PS210 - 110-120VAC input power supplies that deliver (2) amps @ 24VDC to (1) PTC
fused outputs. (1)  solid-state input triggers, protects system relays
from shorts, grounds and surges. It’s linear design makes it a perfect
match for electric locks, motor driven exit devices, electric strikes,
and mag locks.
more info
   
 
Signup for our Newsletter