|
|
|
|
|
|
Concealed Door Loop for Continuous and Butt Hinge Applications
|
|
|
This patented Concealed Door Loop (CDL) is a low cost method of transferring low voltage power from the door frame to the locking device. Whereas typical door loops are surface mounted and remain constantly visible, the CDL slides into the door and/or frame completely concealing itself when the door is closed. Designed for Continuous and Butt hinge applications that are either full mortise, half mortise or half surface and have a standard throw. Commonly installed where ETH hinges are cost prohibitive and surface door loops are not desired. The CDL’s aesthetic appeal will benefit retrofits and new installations alike.
Models for butt & continuous hinges:
CDL-AL - Standard 6" length with aluminum finished caps
CDL-BLK - Standard 6" length with black anodized finished caps
CDL-AL-FX - Standard 6" length with aluminum finished caps & 1 side fixed
CDL-BLK-FX - Standard 6" length with black anodized finished caps & 1 side fixed
* For narrow frame and door conditions see 3/4” pivot models (CDL-AL-EXT, CDL-BLK-EXT)
Features:
Durable finish
Special 1/4" flexible armored conduit
Easy installation
Supports up to 18O degree swing
Variable mounting locations
No hassle 3-Year Warranty
Functionality:
|
|
|
|
|
|
|
|
|
|
Surface Applied Door Loop
|
|
|
The door loop is a low cost method of transferring low voltage power from the door frame to the locking device. Door loops are commonly used with electric mortise & cylindrical locks, electric exit trims and latch pullback devices.
Configurations:
DL-24AL - Standard 24" length with aluminum finish
DL-24D - Standard 24" length with duronatic finish
Features:
Durable powder coated finish
Pre-drilled holes in base
Flexible armored conduit
No hassle 3-Year Warranty
|
|
|
|
|
|
|
|
|
|
Concealed Door Loop for Offset Pivot Applications
|
|
|
This patented Concealed Door Loop (CDL) is a low cost method of transferring low voltage power from the door frame to the locking device. Whereas typical door loops are surface mounted and remain constantly visible, the CDL slides into the frame completely concealing itself when the door is closed. Commonly used in storefront or main entrance applications with 3/4” offset pivots that swing up to 105°. The CDL’s aesthetic appeal will benefit retrofits and new installations alike.
Models for 3/4" offset Pivots:
CDL-AL-EXT - 12" length with aluminum finished caps - door side fixed, frame side extended for wire guidance
CDL-BLK-EXT - 12" length with black anodized finished caps - door side fixed, frame side extended for wire guidance
Features:
Durable finish
Special 1/4" flexible armored conduit
Easy installation
Supports up to 105 degree swing
Variable mounting locations
No hassle 3-Year Warranty
|
|
|
|
|
|
|
|
|
|
CA-5 Knuckle Heavy Weight Tranfer Hinge - ETH
|
|
|
The Energy Transfer Hinge (ETH) is the ideal way to pass low voltage power from the hinge jamb to the lockset without having any exposed wires. These hinges are commonly used with electric mortise & cylindrical locks, electric strikes (when on a pair of doors), electric exit trims, latch pullback devices, door mounted card readers and low voltage door lights. We can modify almost any hinge and we maintain a large inventory of most major hinge brands in various sizes and finishes. Contact us if what you need is not listed.
Configurations:
ETH2W: 2 Wire (20 gauge) - 4A@24V (per pair)
ETH4W/6W: 4/6 Wire (26 gauge) - 1A@24V (per pair)
ETH8W/1OW/12W: 8/10/12 Wire (28 gauge) - 1A@24V (per pair)
Configurations Available for Electric Latch Retraction:
ETH2WH: 2 Wire (18 gauge) - 5A (16 amp in-rush for 300 ms.)
ETH4WH - ETH12WH: 4 - 12 Wire (2 wires @ 18 ga. + 2-10 wires 28 ga.)
Features:
UL-F Rated
4' lead available at no extra charge
Center located wire access holes for easy installation (5 Knuckle std. wt.)
Non-conductive wire access cap for added wire protection
No hassle 3-Year Warranty
|
|
|
|
|
|
|
|
|
|
CA-3 Knuckle Heavy Weight Tranfer Hinge - ETH
|
|
|
The Energy Transfer Hinge (ETH) is the ideal way to pass low voltage power from the hinge jamb to the lockset without having any exposed wires. These hinges are commonly used with electric mortise & cylindrical locks, electric strikes (when on a pair of doors), electric exit trims, latch pullback devices, door mounted card readers and low voltage door lights. We can modify almost any hinge and we maintain a large inventory of most major hinge brands in various sizes and finishes. Contact us if what you need is not listed.
Configurations:
ETH2W: 2 Wire (20 gauge) - 4A@24V (per pair)
ETH4W/6W: 4/6 Wire (26 gauge) - 1A@24V (per pair)
ETH8W/1OW/12W: 8/10/12 Wire (28 gauge) - 1A@24V (per pair)
Configurations Available for Electric Latch Retraction:
ETH2WH: 2 Wire (18 gauge) - 5A (16 amp in-rush for 300 ms.)
ETH4WH - ETH12WH: 4 - 12 Wire (2 wires @ 18 ga. + 2-10 wires 28 ga.)
Features:
UL-F Rated
4' lead available at no extra charge
Center located wire access holes for easy installation (5 Knuckle std. wt.)
Non-conductive wire access cap for added wire protection
No hassle 3-Year Warranty
|
|
|
|
|
|
|
|
|
|
Storefront ETH Electric Transfer Hinge (Flat Dark Bronze)
|
|
|
Electric Hinge specifically manufactured with rounded corners for use with storefront system's flat dark bronze hinges. The flat dark bronze color matches the manufacturers hinges that are used so all the hinges will match. The electric hinges have 4 wires, 2 each 18 gauge wires rated at 5 amps and 2 each 26 gauge wire for signal if needed. 3 year warranty. UL listed.
|
|
|
|
|
|
|
|
|
|
Storefront ETH Electric Transfer Hinge (Brushed Stainless Steel)
|
|
|
Electric Hinge specifically manufactured with rounded corners for use with storefront system's stainless steel hinges. The brushed stainless steel finish matches the manufacturers hinges that are used so all the hinges will match. The electric hinges have 4 wires, 2 each 18 gauge wires rated at 5 amps and 2 each 26 gauge wire for signal if needed. 3 year warranty. UL listed.
|
|
|
|
|
|
|
|
|
|
Storefront ETH Electric Transfer Hinge (Gloss Dark Bronze)
|
|
|
Electric Hinge specifically manufactured with rounded corners for use with Vistawall, Coral and other storefront system's Regent gloss dark bronze hinges. The gloss dark bronze color matches the manufacturers hinges that are used so all the hinges will match. The electric hinges have 4 wires, 2 each 18 gauge wires rated at 5 amps and 2 each 26 gauge wire for signal if needed. 3 year warranty. UL listed.
|
|
|
|
|
|
|
|
|
|
CA- Power Transfer Pivot - ETH
|
|
|
The Energy Transfer Pivot Hinge is available in the same wire configurations s the butt hinges. It's a great way to pass power from the hinge jamb to the door and have no exposed wires or cords. We maintain an inventory of our own Command Access intermediate pivot hinge. We also modify other manufacturers pivots if sent to us.
Configurations:
ETH2W = 2(20ga) wire - 4A @ 24V (per pair)
ETH4W = 4(26ga) wire - 1A @ 24V (per pair)
ETH6W = 6(26ga) wire - 1A @ 24V (per pair)
ETH8W = 8(28ga) wire - 1A @ 24V (per pair)
ETH10W = 10(28ga) wire - 1A @ 24V (per pair)
Configurations for Electric Latch Pullback:
ETH2WH = 2(18ga) wire
ETH4WH = 2(18ga) + 2(28ga) wire
ETH6WH = 2(18ga) + 4(28ga) wire
ETH8WH = 2(18ga) + 6(28ga) wire
Features:
Non-conductive wire access cap for added wire protection
4' lead available at no charge
No hassle 3 year warranty
|
|
|
|
